Mapei 111 UltraColor Plus Silver Grey Grout 2kg

Product Information

Mapei Kerapoxy Epoxy Tile Grout is a two-component, epoxy-resin based product with silica sand and special components, with excellent resistance to acids and excellent cleanability. This is a product with very low emission of volatile organic compounds and is classified Emicode EC1 R Plus by GEV when used for grouting. The following features are obtained when used correctly: For those in search of a touch of glam, we even supply a selection of tile grout glitter additives in gold, silver, grey, pink and more. Perfect for giving tiled areas some added sparkle to bounce light around the room, this glitter can be added to your grout mix before you apply. Delivery charges vary for the following postcodes and will be delivered between 5-7 working days to the following postcodes: GY, HS, IM, IV41,IV30, IV42, IV44 – 49, IV55, IV56, JE, KA27 – 29, KW1 – 14, KW15 – 17, PA21 – 38, PA20, PA40+, PH9, PH15 – 20, PH32 – 44, PH49, PH50, TR21 – 25, ZE. When resistance to acids or, where extreme cleanliness or sterile conditions are required, use a suitable acid-resistant epoxy grout. For Mapei, “zero impact on climate change” means that CO 2 emissions measured throughout the life cycle of ULTRACOLOR PLUS using Life Cycle Assessment (LCA) methodology, verified and certified with EPDs, have been offset through the acquisition of certified carbon credits in support of renewable energy and forestry protection projects. A commitment to the planet, to people and to biodiversity.

Mapei Ultracolor Plus forms a smooth, compact finished surface with optimum resistance to abrasion, compression and flexural strength, and good resistance to acids with a pH > 3. Floors are ready for light foot traffic after approx. 3 hours. Surfaces grouted with Mapei Ultracolor Plus may be put into service after 24 hours. Basins and swimming pools may be filled up 48 hours after grouting. After grouting with Mapei Kerapoxy, floors and walls should be cleaned immediately, before the product dries. Wet the surface thoroughly and emulsify with an abrasive pad for cleaning joints (such as Scotch-Brite or Kerakoll Cleaning Pads), making sure not to wash-out the joints. When cleaning walls, the cleaning pad should be fully soaked with water. The excess liquid can be removed with a hard cellulose sponge (e.g. Kerakoll Cellulose Sponge Float), and should be replaced when too full of resin. Use the same type of sponge for the final tooling of the grout. It is very important that once the finishing process has ended, no traces of Mapei Kerapoxy are left on the tile surface because it will be very difficult to remove. It is therefore necessary to frequently rinse the sponge with clean water during the cleaning process.When finishing large floor surface areas, use a rotary, disc-type power float with Scotch-Brite® abrasive pads, well saturated with water. All excess liquid can be removed with a rubber squeegee. The final cleaning cycle may be carried out using Mapei Ultracare Kerapoxy Cleaner for epoxy grout (special cleaning solution for epoxy grout). Mapei Kerapoxy Cleaner may also be used to remove thin residues of grout several hours after application. In such cases, the product must be left to react for longer (15-20 mins.). The efficiency of Mapei Kerapoxy Cleaner depends on the amount of resin residues and how much time has passed since application. Cleaning must always be carried out while “fresh” as described above.

For interior and exterior wall and floor grouting of ceramic tiles, porcelain, terracotta, stone material, glass and marble mosaics

After the final cleaning operation, if the surface still has traces of Mapei Ultracolor Plus due to incorrect application, it may be cleaned down with an acidic cleaner (e.g. Keranet), by following the relevant instructions, at least 24 hours after grouting the joints. Only use Keranet on surfaces which are resistant to acid, and never use it on marble or limestone material. Sponge down the area: using clean water and a damp (not wet) sponge or sponge float, wipe down the tiles and grout lines to remove the remaining grout, ensuring the grout lines have a smooth, even finish. After laying any tiles, you’ll need to choose the right tile grout to help you complete the job and seal your tiles from dirt and moisture - and this is where we can help, too. Prep the area: first and foremost, make sure the adhesive has fully dried, then carefully carve out any excess adhesive, tile spacers, dust and other debris between the tile joints, using a vacuum at the final stage to remove as much as possible. Excellent workability, highly improved compared with traditional epoxy mortars thanks to its creamy consistency, which guarantees faster application times and makes it easier to clean the surfaces, with less waste and easier to obtain a good finish.

Mapei Ultracolor Plus Silver Grey Flexible Grout (5kg)?

For flexible expansion joints or joints subject to movement use an elastic sealant from the Mapei line (e.g. Mapesil AC, Mapesil LM, Mapeflex PU45 FT or Mapeflex PU21).

From our carrier you will receive a text message on the day of the delivery with a 2 hour delivery window. If there any changes or delays you will receive an update via text. Mapei Fuga Fresca: to keep your tile grout refreshed and its colour intact, look no further than Mapei’s Fuga Fresca resin-based grout paint suitable for grout on walls or floors. Minimise water absorption and make tile and grout cleaning a breeze, with colour options including white, grey and silver In areas that may need added protection against stains and chemicals, such as countertops or high-traffic areas, we’d recommend investing in the Mapei Kerapoxy or Mapei Kerapoxy CQ grout. Both tile grouts provide exceptional resistance to acids and boast stress-free cleanability, meaning you can keep your grout lines looking clean and colourful with ease. Expansion and movement joints on walls and floors must never be filled with Mapei Ultracolor Plus. Use a suitable flexible sealant from the MAPEI range.

Delivery & Returns

Acid-resistant bonding of tiles (used as an adhesive in compliance with class R2T specification according to EN 12004 standard). Spread Mapei Kerapoxy with an appropriate grout float, making sure the joints are completely filled. Use the same float, but on edge, to remove excess grout. If hardened and Kerapoxy CQ has to be removed from the joints, use an industrial hot air blower. If hardened localized residues of the product remain bonded to the tiles, use Pulicol 2000 for cleaning. Grouting of surfaces where a high protection against the formation and proliferation of micro-organisms is required.